Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
They are making a few good pointers about How to Install a Bathtub Yourself as a whole in this content below.
Installing a bath tub isn't precisely rocket science, however it does need strong plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bathtub with a brand-new one is likewise a moderately difficult job. If the old bathtub is easily obtainable, the project can move easily; if you have to open a wall to eliminate the old bathtub and also place the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will need an assistant to move out the old tub and set in the new one. Make sure you have actually qualified yourself for the task and are comfortable attempting it. Instead of employing a service provider to take over a halfway-completed project, it is far better to think about employing one prior to you start. Chances are you may need an expert plumber to make tube links.
This short article will help you set up a brand-new tub in your shower room if you have actually already acquired a brand-new bathtub and also don't require to transform the arrangement of your previous water pipes.
Your devices as well as product checklist ought to make up the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water supply. After doing so, turn on the taps to drain pipes any type of water remaining in the system. The process of eliminating the existing faucets can be quite problematic due to the limited accessibility that is often the situation.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a towel ready for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from turning during this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old securing substance.
Prior to moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the various other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly require lowering couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin making certain that the washers remain in place between the faucet and the sink. Protect the tap in position with the producer given backnut. Once the faucet is firmly in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former type should be connected to the faucet finishes initially, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.
Setting up the Bathtub
Using the two wood boards under its feet, position the bath tub in the called for position. The wooden boards are useful in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the level and readjusting the feet on the tub up until the level reads degree.
To set up taps, fit all-time low of the outermost flexible tap port to the ideal supply pipeline by making a compression join; after that do the same for the other faucet.
Activate the supply of water and check all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill the tub and also inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, repair the bath paneling as defined in the producer's user's manual. Tiling and securing around the bathtub ought to wait up until the tub has actually been made use of at least once as this will resolve it into its final setting.
Getting ready for the Setup
First of all, the supporting framework supplied with the bath should be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is very important to make certain that if the tap includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps unit to avoid stress on the tub.
Fit the versatile tap ports to the bottom of the two faucets making use of 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you utilize every one of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be suited its final position.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to split a stiff seal, triggering the water to pass through the wall surface between the bath as well as the tiling, causing issues with moisture and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your fixtures and also fittings. They are sold in tubes as well as cartridges, and can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill the tub with water before sealing, to permit the movement experienced when the bathtub remains in use. The sealant can split relatively very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also easily available on the marketplace. It is suggested to fit the floor tiles using waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very enthusiastic about Installing A Bathtub and I hope you enjoyed the entire blog entry. Do you know another person who is fascinated by the topic? Please feel free to share it. We thank you for reading our article about How to Install a Bathtub.
Request our emergency plumbing support. Report this page